A Novel Self-aligned and Maskless Process for Formation of Highly Uniform Arrays of Nanoholes and Nanopillars
- First Online:
- Cite this article as:
- Wu, W., Dey, D., Memis, O.G. et al. Nanoscale Res Lett (2008) 3: 123. doi:10.1007/s11671-008-9124-6
- 1.9k Views
Fabrication of a large area of periodic structures with deep sub-wavelength features is required in many applications such as solar cells, photonic crystals, and artificial kidneys. We present a low-cost and high-throughput process for realization of 2D arrays of deep sub-wavelength features using a self-assembled monolayer of hexagonally close packed (HCP) silica and polystyrene microspheres. This method utilizes the microspheres as super-lenses to fabricate nanohole and pillar arrays over large areas on conventional positive and negative photoresist, and with a high aspect ratio. The period and diameter of the holes and pillars formed with this technique can be controlled precisely and independently. We demonstrate that the method can produce HCP arrays of hole of sub-250 nm size using a conventional photolithography system with a broadband UV source centered at 400 nm. We also present our 3D FDTD modeling, which shows a good agreement with the experimental results.
With nanotechnology becoming widely used, there is an increasing demand for rapid, parallel fabrication strategies for nanoholes and nanopillars. Some applications that require repetitive uniform nanoholes and nanopillars over large area are photonic crystals , memory devices , nanofiltration , solar cells , artificial kidneys , etc. Conventional photolithography techniques cannot satisfy the requirements of the nanopatterns due to the wavelength limit of current light source. Novel techniques like X-ray, electron beam, and focused ion beam are either slow or expensive for fabricating such repetitive patterns over large areas. Micro- and nanospheres that have highly uniform sizes and could easily produce a hexagonally close packed (HCP) self-assembled monolayer have attracted widespread attention for forming large areas of periodic nanostructures. One important example is Nanosphere Lithography (NSL) technique , which uses planar ordered arrays of polystyrene micro/nanospheres as a lithography mask to generate ordered nanoscale arrays on the substrate. However, the technique is always used for production of periodic particle arrays and it strictly requires the nanospheres to form a perfect hexagonal closed monolayer.
Here we present a novel photolithography technique, Nanosphere Photolithography (NSP), utilizing the self-assembled planar ordered single layer transparent spheres to generate sub-wavelength regular patterns over a large area on common photoresist. Previous studies show that the silica and polystyrene micro/nanospheres would act as super-lenses for the UV light . The beam waist of the focused light would be much smaller than the wavelength of the light and the intensity would be many times stronger. Our full 3D finite difference time domain (3D-FDTD) calculations show that the beam waist is a very weak function of the sphere diameters and hence extremely uniform pattern size can be achieved. It is also possible to obtain the uniform nanopatterns of tunable sizes by changing the exposure energy and develop time of the photoresist, as well as controlling the spacing and density of the patterns using spheres of different diameters. NSP technique does not have special requirement for the coverage of the spheres, because the area of photoresist without the spheres or with multilayers of spheres cannot absorb enough photon energy to be developed.
Experiment and Results
All experiments are done in class-100 clean room. Two kinds of photoresists, AZ 5214-E and Shipley 1805, and two types of spheres, silica and PS, were used to form HCP arrays on top of the photoresist. About 10 wt.% aqueous suspensions of transparent silica or PS spheres were diluted by DI water down to 0.05 wt.% for both types of the spheres. Based on our simulations, it was found that the focusing intensity of silica spheres was smaller than that of PS spheres of the same sizes on the photoresist. So after using AZ 5214-E for the PS spheres, we considered photolithography with Shipley 1805 using silica spheres. The samples were exposed by a conventional photolithography instrument (Quintel Q-2000) under low exposure energy with a broad wavelength centered at 400 nm. Before development, the spheres can be removed by either HF acid solution or ultrasonication in DI water. The photoresist was developed using an AZ-300 MIF developer.
We have demonstrated a novel maskless and self-aligned sub-wavelength photolithography technique for forming highly uniform arrays of nanoholes and nanopillars. The technique utilizes the self-assembled property of micro- and nanospheres and applies them into the maturely developed photolithography system. It is simple, fast, economical, and compatible with current photolithography sources and photoresists, and hence it can be alternatively applied into some areas.