Skip to main content
Log in

Asymmetric Rolling of Interstitial-Free Steel Using Differential Roll Diameters. Part II: Microstructure and Annealing Effects

  • Published:
Metallurgical and Materials Transactions A Aims and scope Submit manuscript

Abstract

The effects of annealing on the microstructure, texture, tensile properties, and R value evolution of an IF steel sheet after room-temperature symmetric and asymmetric rolling were examined. Simulations were carried out to obtain R values from the experimental textures using the viscoplastic self-consistent polycrystal plasticity model. The investigation revealed the variations in the textures due to annealing and symmetric/asymmetric rolling and showed that the R values correlate strongly with the evolution of the texture. An optimum heat treatment for the balance of strength, ductility, and deep drawability was found to be at 873 K (600 °C) for 30 minutes.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5

Similar content being viewed by others

References

  1. H. Takechi: ISIJ Int., 1994, vol. 34, pp. 1–8.

    Article  Google Scholar 

  2. Y. B. Park, L. Kestens, and J. J. Jonas: ISIJ Int., 2000, vol. 40, no. 4, pp. 393-401.

    Article  Google Scholar 

  3. K. Ushioda, S. Takebayashi, and Y.R. Abe: Mater. Manuf. Process., 2010, vol. 25, pp. 185–194.

    Article  Google Scholar 

  4. R. Saha, and R. K. Ray: ISIJ Int., 2008, vol. 48, no. 7, pp. 976-983.

    Article  Google Scholar 

  5. D. Orlov, A. Pougis, R. Lapovok, L. S. Tóth, I. B. Timokhina, P. D. Hodgson, A. Haldar, and D. Bhattacharjee: Metall. Mater. Trans. A, 2013, vol. 44, pp. 4346-4359.

    Article  Google Scholar 

  6. J.-K. Kim, Y.-K. Jee, M.-Y. Huh, and H.-T. Jeong: J. Mater. Sci., 2004, vol. 39, no. 16, pp. 5365-5369.

    Article  Google Scholar 

  7. T. Gow-Yi: J. Mater. Process. Tech., 1998, vol. 86, no. 13, pp. 271-277.

    Google Scholar 

  8. H. Jin, and D. J. Lloyd: Mat. Sci. Eng. A, 2007, vol. 465, no. 12, pp. 267-273.

    Article  Google Scholar 

  9. H. Utsunomiya, T. Ueno, and T. Sakai: Scripta Mater., 2007, vol. 57, no. 12, pp. 1109-1112.

    Article  Google Scholar 

  10. T. Sakai, K. Yoneda, and S. Osugi: Mater. Sci. Forum., 2005, vol. 495-497, pp. 597-602.

    Article  Google Scholar 

  11. R. Lapovok, L. S. Tóth, M. Winkler, and S. L. Semiatin: J. Mater. Res., 2009, vol. 24, no. 2, pp. 459-469.

    Article  Google Scholar 

  12. D. Orlov, R. Lapovok, L.S. Tóth, I.B. Timokhina, P.D. Hodgson, D. Bhattacharjee, and A. Haldar: Mater. Sci. Forum., 2010, vol. 654-656, pp. 1255–1258.

    Article  Google Scholar 

  13. R. Lapovok, D. Orlov, I. B. Timokhina, A. Pougis, L. S. Tóth, P. D. Hodgson, A. Haldar, and D. Bhattacharjee: Metall. Mater. Trans. A, 2012, vol. 43, pp. 1328-1340.

    Article  Google Scholar 

  14. D. Orlov, R. Lapovok, L. S. Tóth, I. B. Timokhina, P. D. Hodgson, D. Bhattacharjee, and A. Haldar: Mater. Sci. Forum., 2012, vol. 706 - 709, pp. 2788-2793.

    Article  Google Scholar 

  15. L.S. Tóth, B. Beausir, D. Orlov, R. Lapovok, and A. Haldar: J. Mater. Process. Technol., 2012, vol. 212, no. 2, pp. 509-515.

    Article  Google Scholar 

  16. R. A. Lebensohn, and C. N. Tomé: Acta. Metall. Mater., 1993, vol. 41, no. 9, pp. 2611-2624.

    Article  Google Scholar 

  17. D. Daniel, and J. J. Jonas: Metall. Trans. A, 1990, vol. 21, pp. 331-343.

    Article  Google Scholar 

  18. L. S. Toth, and P. V. Houtte: Texture Microstruct., 1992, vol. 19, pp. 229-244.

    Article  Google Scholar 

  19. R. D. Doherty, D. A. Hughes, F. J. Humphreys, J. J. Jonas, D. J. Jensen, M. E. Kassner, W. E. King, T. R. McNelley, H. J. McQueen, and A. D. Rollett: Mat. Sci. Eng. A, 1997, vol. 238, no. 2, pp. 219-274.

    Article  Google Scholar 

  20. F.J. Humphreys, and M. Hatherly: Recrystallization and Related Annealing Phenomena, 2nd ed., Elsevier Science, Tarrytown, 1996.

    Google Scholar 

  21. C. Xu, Z. Horita, and T. G. Langdon: Acta Mater., 2007, vol. 55, no. 1, pp. 203-212.

    Article  Google Scholar 

  22. D. Orlov, Y. Todaka, M. Umemoto, Y. Beygelzimer, and N. Tsuji: Mater. Trans., 2012, vol. 53, no. 1, pp. 17-25.

    Article  Google Scholar 

  23. A. Vinogradov, M. Maruyama, Y. Kaneko, and S. Hashimoto: Philos. Mag., 2011, vol. 92, no. 6, pp. 666-689.

    Article  Google Scholar 

Download references

Acknowledgments

The authors acknowledge the use of equipment within the Monash Centre for Electron Microscopy, including SEM FEI Quanta 3D funded through the Australian Research Council Grant LE0882821. The authors gratefully acknowledge financial support of this work by a Linkage Industrial project LP0989455 of the Australian Research Council.

Author information

Authors and Affiliations

Authors

Corresponding author

Correspondence to Dmitry Orlov.

Additional information

Manuscript submitted October 10, 2012.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Orlov, D., Lapovok, R., Toth, L.S. et al. Asymmetric Rolling of Interstitial-Free Steel Using Differential Roll Diameters. Part II: Microstructure and Annealing Effects. Metall Mater Trans A 45, 447–454 (2014). https://doi.org/10.1007/s11661-013-1958-6

Download citation

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11661-013-1958-6

Keywords

Navigation