Measuring sub nanometre sizes using dynamic light scattering
- First Online:
- Cite this article as:
- Kaszuba, M., McKnight, D., Connah, M.T. et al. J Nanopart Res (2008) 10: 823. doi:10.1007/s11051-007-9317-4
- 4.1k Downloads
Dynamic light scattering (DLS) measures time-dependent fluctuations in the scattering intensity arising from particles undergoing random Brownian motion. Diffusion coefficient and particle size information can be obtained from the analysis of these fluctuations. This paper discusses the factors which will influence the lower size limit of DLS and reports the use of sucrose as a test sample to probe this lower limit of the technique. Hydrodynamic diameter values of less than 1 nm are obtained by the use of 173° backscatter detection that is applied to increase the sensitivity of DLS. The peak means (with standard deviations) obtained for the intensity and volume data from a series of sucrose concentrations, ranging from 5 to 35% w/v, were measured as DI,Mean = 0.82 nm (0.11 nm) and DV,Mean = 0.62 nm (0.05 nm), respectively. These sucrose results suggest that sub nanometer measurements are achievable with a precision of 0.1 nm. Evidence to support these size results for sucrose is discussed.
KeywordsDynamic light scatteringMolecular sizeSub nanometer sizeLower size limitLower concentration limitBackscatter detectionInstrumentationNanotechnology
Measuring the size of small molecules is currently of great interest in many applications. For example, proteins are being utilized directly in the pharmaceutical industry as active agents in drugs (Akagi et al. 2007; Nam et al. 2002). The size of the molecules can be used as a quality control measure. Similarly during the production of nanoparticles, the size of the particles can be used as a measure in a quality control process (Hu et al. 2004; Zheng et al. 2002; Pascal et al. 1999). However, there are very few techniques available for the measurement of small molecules and particles in solution.
The lower size limit of the dynamic light scattering technique depends on the amount of excess scattered light produced. This excess is the difference in scattering between the molecule or particle being studied and the dispersant it is prepared in. This in turn depends on a number of factors such as the refractive indices of the molecule and dispersant, the concentration of the sample, the power and wavelength of the laser used, the sensitivity of the detector and the optical configuration of the instrument. Inevitably, as the size of the molecule or particle becomes smaller, the amount of excess scattering produced reduces.
Conventional dynamic light scattering instruments use a detection angle of 90° and this optical configuration may not be sensitive enough for the successful measurement of small particles or molecules even with the incorporation of a powerful laser at low wavelength. An optical configuration that allows measurements of samples at lower concentrations of smaller sizes is backscatter detection. At 173° backscatter, the scattering volume observed at the detector is about 8 times the volume observed with classical 90° scattering optics. This results in an 8-fold increase in the detected count rate, which is directly correlated with instrument sensitivity, or the ability to measure small particles at lower concentrations. The use of fiber optics in combination with this optical arrangement ensures that the signal to background ratio, or more correctly, the intercept of the correlation function, is not degraded at high detection volumes as it would with ‘classical’ geometric optics (Peters 2000). Increasing the count rate while simultaneously reducing the intercept of the correlation function is of little value. This optical configuration provides the exceptional sensitivity that is required for measuring the size of nanoparticles and molecules at low concentrations.
This paper explores the lower limits of size which are measurable by dynamic light scattering using sucrose as a test sample. The measurement of sucrose at a 173° detection angle is discussed and the advantages of using backscatter detection for characterizing sub nanometer sized samples is highlighted. Comparisons are made with size estimates using other techniques.
Sucrose solutions of 5, 10, 15, 20, 25, 30 and 35% w/v, respectively were prepared in ultra pure water and filtered through Whatman Anotop 0.02 μm pore size filters (cat. no. 6809–3002). All chemicals used in this study were Analar grade or better.
Measurements of all sucrose concentrations were made on a Malvern Zetasizer Nano S (Malvern Instruments Ltd., UK) with a detection angle of 173°. All measurements in this study were taken at a temperature of 25 °C. At least 3 repeat measurements on each sample were taken to check for result repeatability. The Nano S uses a 4 mW He–Ne laser operating at a wavelength of 633 nm. The intensity size distributions were obtained from analysis of the correlation functions using the Multiple Narrow Modes algorithm in the instrument software. This algorithm is based upon a non-negative least squares fit (Twomey 1997; Lawson and Hanson 1995). These intensity particle size distributions were converted into volume using Mie theory (Mie 1908). The optical properties of the sucrose molecules were not considered important because their size is significantly lower than the incident laser wavelength used.
The technique of DLS measures the diffusion coefficients of molecules or particles undergoing Brownian motion. To convert the measured diffusion coefficient data into a hydrodynamic size, the viscosity of the sample must be entered into Stokes-Einstein’s equation as highlighted in the Introduction section of this paper. There are a number of ways in determining what the correct viscosity value for the samples that should be used. For example, the relative viscosity of known sucrose solutions with respect to water can be found in the literature (CRC Handbook 2006–2007) or the viscosities of the sucrose solutions can be determined with an appropriate viscometer. However, because the technique of dynamic light scattering measures the diffusion speed of molecules or particles undergoing Brownian motion, a useful method of determining the appropriate viscosity value is to dope each sucrose sample with a known size of polystyrene latex standard. In this study, 10 μl of a 150 nm polystyrene latex (cat. no. 3150 A) obtained from Duke Scientific (Palo Alto, US) was added to 990 μl of the appropriate sample. Comparison of the size obtained for the latex dispersed in sucrose (assuming the viscosity of water) with the size obtained for the same latex dispersed in 10 mM NaCl (the true hydrodynamic diameter), allows for the determination of the viscosities of the sucrose solutions. Measurements were made in 10 mM NaCl in order to suppress the electrical double layer according to the International Standard ISO13321 (1996). This method of adding latex to the sucrose solutions works well, as the scattering from the larger latex particles is much greater than that from the sucrose molecules.
Results and discussion
The results obtained for a 150 nm Duke Scientific polystyrene latex standard doped into 10 mM NaCl and various concentrations of sucrose. The table contains the intensity-averaged diameter in nanometers, the polydispersity index values and the calculated viscosities
Sucrose concentration (% w/v)
Intensity-averaged diameter (nm)
Calculated viscosity (mPa s)
0 (Only 10 mM NaCl)
The table contains the intensity-averaged diameter in nanometers, the polydispersity index values and the calculated viscosities. The intensity-averaged particle diameter and the polydispersity index (PDI) values (an estimate of the distribution width) were calculated from the cumulants analysis as defined in ISO13321 (1996). The polydispersity index values are very sensitive to the presence of aggregates or dust. A monodisperse sample such as the polystyrene latex used in this study would be expected to give a PDI value of less than 0.05. All the PDI values reported in Table 1 are less than 0.05 indicating that the latex was not affected at any of the sucrose concentrations. The calculated viscosities for the various sucrose concentrations were determined by dividing the viscosity of 10 mM NaCl (0.8872 mPa s) by the ratio of the intensity-averaged diameter for the latex in 10 mM NaCl to the apparent intensity-averaged diameter for the latex in the appropriate sucrose concentration. The viscosity required for DLS measurements is the viscosity that the particle being studied experiences as it undergoes Brownian motion. This is the most appropriate way of obtaining this information and is a valid technique as long as the latex being used is not being affected by the dispersant it is doped into and as long as the introduction of latex does not significantly alter the sample viscosity. In this study, such a small aliquot addition to each sucrose concentration would not be expected to affect the viscosity of the solutions.
The correlation functions shown in Fig. 2 exhibit two visible decay rates. The rapid decay rates seen in delay times up to 10 μs are interpreted as arising from the diffusion of sucrose molecules. The slower decay rates seen near to the baseline of the correlation functions (at correlator delay times of between 10 and 1,000 μs, respectively) are probably due to collective diffusion of the sucrose molecules. This hypothesis is supported by the increase in amplitude of this slow decay rate with increasing sucrose concentration.
Sucrose concentration (% w/v)
Intensity distribution data
Volume distribution data
Peak 1 mean (nm)
Peak 1 mode (nm)
Peak 1 mean (nm)
Peak 1 mode (nm)
The results presented in this paper indicate that the measurement of sub nanometer sizes are now possible using dynamic light scattering if samples are carefully prepared and an appropriate optical configuration is used. The use of backscatter detection in combination with fiber optics provides exceptional sensitivity with retention in the signal to noise sufficient to be able to measure samples at these small sizes.