Skip to main content
SpringerLink
Log in

Limit analysis of FGM circular plates subjected to arbitrary rotational symmetric loads using von-Mises yield criterion

  • Published:
Acta Mechanica Aims and scope Submit manuscript

Abstract

In this paper, employing the limit analysis theorem, critical loading on functionally graded (FG) circular plate with simply supported boundary conditions and subjected to an arbitrary rotationally symmetric loading is determined. The material behavior follows a rigid-perfectly plastic model and yielding obeys the von-Mises criterion. In the homogeneous case, the highly nonlinear ordinary differential equation governing the problem is analytically solved using a variational iteration method. In other cases, numerical results are reported. Finally, the results are compared with those of the FG plate with Tresca yield criterion and also in the homogeneous case with those of employing the von-Mises yield criterion. A good correspondence is observed between the calculated results and those available in the literature.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Prager W.: An Introduction to Plasticity. Addison-Wesley, Reading (1959)

    MATH  Google Scholar 

  2. Horne M.: Plastic theory of structures. The MIT Press, Cambridge (1971)

    Google Scholar 

  3. Mansfield E.H.: Studies in collapse analysis of rigid-plastic plates with a square yield diagram. Proc. R. Soc. Lond. Ser. A Math. Phys. Sci. 241, 311–338 (1958)

    Article  MathSciNet  Google Scholar 

  4. Hodge P.: Limit Analysis of Rotationally Symmetric Plates and Shells. Englewood Cliffs, Prentice-Hall (1963)

    MATH  Google Scholar 

  5. Kargarnovin, M.H., Ghorashi, M.: Limit analysis of circular plate subjected to an arbitrary rotational symmetric loading. Proceedings of the 3rd International Conference on Computational Plasticity, vol. 1. pp. 2149–2159 (1992)

  6. Kargarnovin M.H., Faghidian S.A., Farjami Y., Farrahi G.H.: Application of homotopy-Padé technique in limit analysis of circular plates under arbitrary rotational symmetric loading using von-mises yield criterion. Commun. Nonlinear Sci. Numer. Simul. 15, 1080–1091 (2010)

    Article  MathSciNet  MATH  Google Scholar 

  7. Lance R.: On automatic construction of velocity fields in plastic limit analysis. Acta Mech. 3, 22–33 (1967)

    Article  MATH  Google Scholar 

  8. Fussl J., Lackner R., Eberhardsteiner J., Mang H.: Failure modes and effective strength of two-phase materials determined by means of numerical limit analysis. Acta Mech. 195, 185–202 (2008)

    Article  Google Scholar 

  9. Xuan F.Z., Li P.N., Tu S.T.: Limit load analysis for the piping branch junctions under in-plane moment. Int. J. Mech. Sci. 48, 460–467 (2006)

    Article  MATH  Google Scholar 

  10. Milani G.: 3D FE limit analysis model for multi-layer masonry structures reinforced with FRP strips. Int. J. Mech. Sci. 52, 784–803 (2010)

    Article  Google Scholar 

  11. Sadeghi H., Baghani M., Naghdabadi R.: Strain gradient elasticity solution for functionally graded micro-cylinders. Int. J. Eng. Sci. 50, 22–30 (2012)

    Article  MathSciNet  Google Scholar 

  12. Kargarnovin M.H., Faghidian S.A., Arghavani J.: Limit analysis of FGM circular plates subjected to arbitrary rotational symmetric loads. Int. J. Aero. Mech. Eng. 1, 190–195 (2007)

    Google Scholar 

  13. Baghani M., Jafari-Talookolaei R.A., Salarieh H.: Large amplitudes free vibrations and post-buckling analysis of unsymmetrically laminated composite beams on nonlinear elastic foundation. Appl. Math. Model. 35, 130–138 (2011)

    Article  MathSciNet  MATH  Google Scholar 

  14. Baghani M., Fattahi M., Amjadian A.: Application of the variational iteration method for nonlinear free vibration of conservative oscillators. Sci. Iran 19, 513–518 (2012)

    Article  Google Scholar 

  15. He J.H., Wu X.H.: Variational iteration method: new development and applications. Comput. Math. Appl. 54, 881–894 (2007)

    Article  MathSciNet  MATH  Google Scholar 

  16. Koizumi M., Niino M.: Overview of FGM research in Japan. MRS Bull. 20, 19–210 (1995)

    Google Scholar 

  17. Schulz U., Peters M., Bach F.W., Tegeder G.: Graded coatings for thermal, wear and corrosion barriers. Mater. Sci. Eng. A Struct. 362, 61–80 (2003)

    Article  Google Scholar 

  18. Tamura, I., Tomota, Y., Ozawa, M.: Strength and ductility of Fe-Ni-C alloys composed of austenite and martensite with various strength. In: Proceedings of the Third International Conference on Strength of Metals and Alloys, vol. 1, pp. 611–615, Institute of Metals, Cambridge (1973)

  19. Jin Z.H., Doddas R. Jr.: Crack growth resistance behavior of a functionally graded material: computational studies. Eng. Fract. Mech. 71, 1651–1672 (2004)

    Article  Google Scholar 

  20. Guowei M., Iwasaki S., Miyamoto Y., Deto H.: Plastic limit analyses of circular plates with respect to unified yield criterion. Int. J. Mech. Sci. 40, 963–976 (1998)

    Article  MATH  Google Scholar 

  21. Guowei M., Hao H., Iwasaki S.: Plastic limit analysis of clamped circular plate with unified yield criterion. Struct. Eng. Mech. 7, 515–525 (1999)

    Google Scholar 

  22. Ma G., Hao H., Iwasaki S.: Unified plastic limit analyses of circular plates under arbitrary load. J. Appl. Mech. T ASME 66, 568–570 (1999)

    Article  Google Scholar 

  23. Ghorashi M., Daneshpazhooh M.: Limit analysis of variable thickness circular plates. Comput. Struct. 79, 461–468 (2001)

    Article  Google Scholar 

  24. He J.H.: Variational iteration method-some recent results and new interpretations. J. Comput. Appl. Math. 207, 3–17 (2007)

    Article  MathSciNet  MATH  Google Scholar 

  25. Jafari H., Saeidy M., Baleanu D.: The variational iteration method for solving n-th order fuzzy differential equations. Cent. Eur. J. Phys. 10, 76–85 (2011)

    Article  Google Scholar 

  26. Baghani M.: Analytical study on size-dependent static pull-in voltage of microcantilevers using the modified couple stress theory. Int. J. Eng. Sci. 54, 99–105 (2012)

    Article  MathSciNet  Google Scholar 

  27. Ghorashi M.: Limit analysis of circular plates subjected to arbitrary rotational symmetric loadings. Int. J. Mech. Sci. 36, 87–94 (1993)

    Article  Google Scholar 

  28. Leu S.Y.: Convergence analysis and validation of sequential limit analysis of plane-strain problems of the von mises model with non-linear isotropic hardening. Int. J. Numer. Meth. Eng. 64, 322–334 (2005)

    Article  MATH  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. School of Mechanical Engineering, College of Engineering, University of Tehran, P. O. Box 11155-4563, Tehran, Iran

    M. Baghani

  2. Department of Mechanical Engineering, Sharif University of Technology, Tehran, Iran

    B. Fereidoonnezhad

Authors
  1. M. Baghani
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. B. Fereidoonnezhad
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to M. Baghani.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Baghani, M., Fereidoonnezhad, B. Limit analysis of FGM circular plates subjected to arbitrary rotational symmetric loads using von-Mises yield criterion. Acta Mech 224, 1601–1608 (2013). https://doi.org/10.1007/s00707-013-0828-z

Download citation

  • Received:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00707-013-0828-z

Keywords

Search

Navigation