Abstract
This study describes the application of a novel damping insert material for reducing the flow fluctuations in a tandem nozzle supersonic wind tunnel. This new damping material is composed of multi-layer stainless steel wired meshes. The influences of the multi-layer mesh, such as the quantity of the mesh layer and the installed location in the settling chamber, to the freestream quality have been investigated. A Pitot probe instrumented with a Kulite pressure sensor and a hot-wire probe are employed to monitor the flow fluctuation in the test section of the wind tunnel. Thereafter, a combined modal analysis is applied for the disturbance qualification. Additionally, the transient Mach number in the test section is measured. The disturbance qualification indicates that the multi-layer mesh performs well in providing reduction of vorticity reduction and acoustic fluctuations. Comparable flow quality of the freestream was also obtained using a combination of flexible damping materials. However, the life-span of the new damping materials is much longer. The time transient of the Mach number measured in the test section indicates that the mean flow is rather constant over run time. Furthermore, the time-averaged pressure along the settling chamber is recorded and it shows the distribution of pressure drop by settling chamber inserts.
References
Anders J, Stainback P, Beckwith I (1980) New technique for reducing test section noise in supersonic wind tunnels. AIAA J 18(1):5–6
Anders J, Stainback P, Keefe L, Beckwith I (1977) Fluctuating disturbances in a Mach 5 wind tunnel. AIAA J 15(8):1123–1129
Beckwith IE, Chen F-J, Creel Jr T (1986) Design requirements for the NASA Langley supersonic low-disturbance wind tunnel. AIAA Paper, pp 0763
Beckwith IE, Greel T, Chen F-J (1983) Free stream noise and transition measurements in a Mach 3.5 Pilot Quiet Tunnel. AIAA Paper, pp 0042
Estorf M, Wolf T, Radespiel R (2005) Experimental and numerical investigations on the operation of the Hypersonic Ludwieg Tube Braunschweig. In: Fifth European Symposium on Aerothermodynamics for Space Vehicles 563:579
Estorf M, Radespiel R, Schneider SP, Johnson HB, Hein S (2008) Surface-pressure measurements of second-mode instability in quiet hypersonic flow. AIAA Paper, pp 1153
Koulovi D, Radespiel R, Mller-Eigner R (2002) Aerodynamic design parameters of a hypersonic Ludwieg tube nozzle. In: Proceedings of the West East High Speed Flow Fields Conference. Barcelona, Spain
Masutti D, Spinosa E, Chazot O (2012) Disturbance level characterization of a hypersonic blowdown facility. AIAA J 50(12):2720–2730
Norris JD (1965) Calibration of conical pressure probes for determination of local flow conditions at Mach numbers from 3 to 6. NASA TN D-3076
Ross AO (1953) Determination of boundary-layer transition Reynolds numbers by surface-temperature measurements of a 10 degree cone in various NACA supersonic wind tunnels: NACA-TN-3020
Saric WS, White EB (1998) Influence of high-amplitude noise on boundary-layer transition to turbulence. AIAA Paper, pp 2645
Schneider SP, Haven CE (1995) Quiet-flow Ludwieg tube for high-speed transition research. AIAA J 33(4):688–693
Wu J, Liu X, Radespiel R (2016) RANS simulations of a tandem nozzle supersonic wind tunnel. Aerosp Sci Technol 49:215–224
Wu J, Radespiel R (2013) Tandem nozzle supersonic wind tunnel design. Int J Eng Syst Modell Simul 5(1):8–18
Wu J, Radespiel R (2015) Experimental investigation of a newly designed supersonic wind tunnel, Progress in Flight Physics, vol 7, EDP Sciences, pp 123–147
Wu J, Zamre P, Radespiel R (2015) Flow quality experiment in a tandem nozzle wind tunnel at Mach 3. Exp Fluids 56(1):1–18
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Wu, J., Radespiel, R. Damping insert materials for settling chambers of supersonic wind tunnels. Exp Fluids 58, 19 (2017). https://doi.org/10.1007/s00348-017-2310-5
Received:
Revised:
Accepted:
Published:
DOI: https://doi.org/10.1007/s00348-017-2310-5