Skip to main content
SpringerLink
Log in

The effects of cryogenic-treated carbide tools on tool wear and surface roughness of turning of Hastelloy C22 based on Taguchi method

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

In this study, Taguchi method has been applied to evaluate the effect of cryogenically treated tools in turning of Hastelloy C22 super alloy on surface roughness. The optimum parameters (cryogenic treatment, cutting speed, and feed rate) of turning were determined by using the Taguchi experimental design method. In Taguchi method, L9 orthogonal array has been used to determine the signal noise (S/N) ratio. Analysis of ANOVA was carried out to identify the significant factors affecting surface roughness. The statistical analysis indicated that feed rate, with a contribution percentage as high as 87.64 %, had the most dominant effect on machining performance, followed by the cryo-treated tools treatment and cutting speed, respectively. The confirmation tests indicated that it is possible to improve surface roughness significantly by using the Taguchi method. Surface roughness was improved by 28.3 and 72.3 % by shallow (CT1) cryogenic treatment and deep cryogenic treatment (CT2) applied on cementite carbide tools (UT). It found that wear resistance of tungsten carbide insert was increased by shallow and deep cryogenic treatments.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Ulutan D, Ozel T (2011) Machining induced surface integrity in titanium and nickel alloys: a review. Int J Mach Tool Manu 5:250–280

    Article  Google Scholar 

  2. Motorcu AR (2010) Machinability of nickel-based super alloys and titanium alloys, Part II: evaluation of ceramic cutting tools’ performances. Electron J MachTechnol 7:1304–1414

    Google Scholar 

  3. Haynes International, Inc. (2002). HASTELLOY C-22 alloy. (H-2019E) 5-30, www.haynesintl.com

  4. Wang QY, Bai SL, Zhao YH, Liu ZD (2014) Effect of mechanical polishing on corrosion behavior of Hastelloy C22 coating prepared by high power diode laser cladding. App Sur Sci 303:312–318

    Article  Google Scholar 

  5. Bellanger G, Rameau JJ (1996) Behaviour of Hastelloy C22 steel in sulphate solutions at pH 3 and low temperatures. J Mater Sci 31:2097–2108

    Article  Google Scholar 

  6. Hodges S, Laycock NJ, Krouse DP, Virtanen S, Schmutz P, Ryan MP (2007) A micro electrochemical investigation of alloy C22 in chloride solutions below the critical pitting temperature. J Elect Soc 154:C114–C119

    Article  Google Scholar 

  7. Pusavec F, Deshpande A, Yang S, Saoubi RM, Kopac J, Dillon OW, Jawahir IS (2014) Sustainable machining of high temperature Nickel alloy e Inconel 718: part 1 e predictive performance models. J Cl Prod 81:255–269

    Article  Google Scholar 

  8. Akıncıoğlu S, Gökkaya H, Uygur İ (2014) A review of cryogenic treatment on cutting tools. Int J Adv Manuf Technol. doi:10.1007/s00170-014-6755-x

    Google Scholar 

  9. Gandarias A, Lacalle LNL, Aizpitarte X, Lamikiz A (2008) Study of the performance of the turning and drilling of austenitic stainless steels using two coolant techniques. Int J Mach Mac Mater 3:1–17

    Google Scholar 

  10. Arslan Y, Uygur I, Jazdzewska A (2015) The effect of cryogenic treatment on microstructure and mechanical response of AISI D3 tool steel punches. J Manuf Sci Eng 137:1–6

    Article  Google Scholar 

  11. Abia AIF, Barreiro J, Lacalle LNL, Pellitero SMP (2012) Behavior of austenitic stainless steels at high speed turning using specific force coefficients. Int J Adv Manuf Technol 62:505–515

    Article  Google Scholar 

  12. Rodríguez A, Lacalle LNL, Celaya A, Lamikiz A, Albizuri J (2012) Surface improvement of shafts by the deep ball-burnishing technique. Surf Coat Technol 206:2817–2824

    Article  Google Scholar 

  13. Çiçek A, Uygur I, Kıvak T, Ozbek NA (2012) Machinability of AISI 316 austenitic stainless steel with cryogenically treated M35 high-speed steel twist drills. J Manuf Sci Eng 134:25–31

    Article  Google Scholar 

  14. Thakur D, Ramamoorthy B, Vijayaraghavan L (2008) Influence of different post treatments on tungsten carbide–cobalt inserts. Mater Let 62:4403–4406

    Article  Google Scholar 

  15. Reddy TVS, Sornakumar T, Reddy MV, Venkatram R (2009) Machinability of C45 steel with deep cryogenic treated tungsten carbide cutting tool inserts. Int J Refract Met H 27:181–185

    Article  Google Scholar 

  16. Çiçek A, Kıvak T, Uygur I, Ekici E, Turgut Y (2012) Performance of cryogenically treated M35 HSS drills in drilling of austenitic stainless steels. Int J Adv Manuf Technol 60:65–73

    Article  Google Scholar 

  17. Astakhov VP, Godlevskiy V (2012) 3-Delivery of metalworking fluids in the machining zone, metalworking fluids (MWFs) for cutting and grinding. WP 1:79–134

    Article  Google Scholar 

  18. Galanis N, Dimitrios M (2014) Finite element analysis of the cutting forces in turning of femoral heads from AISI 316L stainless steel. Proc World Congr Eng 2:5–10

    Google Scholar 

  19. Candane D, Alagumurthi N, Palaniradja K (2013) Effect of cryogenic treatment on microstructure and wear characteristics of AISI M35 HSS. Int J Mater Sci App 2(2):56–65

    Google Scholar 

  20. Candane D, Alagumurthi N, Palaniradja K (2013) Effect of deep cryogenic treatment on AISI T42 high speed steel. Int J Cur Eng Technol 3:1164–1170

    Google Scholar 

  21. Ramji BR, Murthy HNN, Krishna M (2010) Performance study of cryo-treated HSS drills in drilling cast iron. Int J Eng Sci Tec 2(7):2530–2536

    Google Scholar 

  22. Ramji BR, Narasimha MHN, Krishna M (2010) Performance analysis of cryogenically treated carbide drills in drilling white cast iron. Int JAppl Eng Res 1:553–560

    Google Scholar 

  23. Çiçek A, Kıvak T, Turgut Y, Uygur İ, Ekici E (2011) The influences of deep cryogenic treatment on cutting forces, hole diameters and tool life. IATS 11:33–36

    Google Scholar 

  24. Manna A, Bhattacharayya B (2005) Influence of machining parameters on the machinability of particulate reinforced Al/SiC–MMC. Int J Adv Manuf Technol 25:850–856

    Article  Google Scholar 

  25. Gökkaya H (2006) Experimental investigation of the effect of machining parameters over cutting force and surface roughness in the machinability of AA5052 alloy. J Eng Sci 12:295–301

    Google Scholar 

  26. Nalbant M, Gökkaya H, Toktaş İ, Sur G (2009) The experimental investigation of the effects of uncoated, PVD-and CVD-coated cemented carbide inserts and cutting parameters on Surface roughness in CNC turning and its prediction using artificial neural networks. Robot Comp Integ Manuf 25:211–223

    Article  Google Scholar 

  27. Akıncıoğlu S, Mendi F, Çiçek A, Akıncıoğlu G (2013) ANN-based prediction of surface and hole quality in drilling of AISI D2 cold work tool steel. Int J Adv Manuf Technol 68:197–207

    Article  Google Scholar 

  28. Kıvak T, Samtas G, Çiçek A (2012) Taguchi method based optimisation of drilling parameters in drilling of AISI 316 steel with PVD monolayer and multilayer coated HSS drills. Measurement 45:1547–1557

    Article  Google Scholar 

  29. Baynal K, Terzi Ü (2004) Concurrent optimization of production parameters using Taguchi method and fuzzy logıc. YA/EM’2004 1-5

  30. Ramji BB, Murthy HNN, Krishna M, Raghu MJ (2010) Performance study of cryogenically treated HSS drills in drilling gray cast iron using orthogonal array technique. Res J Appl Sci Eng Technol 2(5):487–491

    Google Scholar 

  31. Asiltürk I, Akkus H (2011) Determining the effect of cutting parameters on surface roughness in hard turning using the Taguchi method. Measurement 44:1697–1704

    Google Scholar 

  32. Zhang JZ, Chen JC, Kirby ED (2007) Surface roughness optimization in an end-milling operation using the Taguchi design method. J Mater Process Tech 184:233–239

    Article  Google Scholar 

  33. José Pontes FJ, Paiva AP, Balestrassi PP, Ferreira JR, Silva MB (2012) Optimization of radial basis function neural network employed for prediction of surface roughness in hard turning process using Taguchi’s orthogonal arrays. Expert Syst Appl 39:7776–7787

    Article  Google Scholar 

  34. Gologlu C, Sakarya N (2008) The effects of cutter path strategies on surface roughness of pocket milling of 1.2738 steel based on Taguchi method. J Mater Process Technol 206:7–15

    Article  Google Scholar 

  35. Günay M, Yücel E (2013) Application of Taguchi method for determining optimum surface roughness in turning of high-alloy white cast iron. Measurement 46:913–919

    Article  Google Scholar 

  36. Asiltürk İ, Neşeli S (2012) Multi response optimisation of CNC turning parameters via Taguchi method-based response surface analysis. Measurement 45:785–794

    Article  Google Scholar 

  37. Fetecau C, Stan F (2012) Study of cutting force and surface roughness in the turning of polytetrafluoroethylene composites with a polycrystalline diamond tool. Measurement 45:1367–1379

    Article  Google Scholar 

  38. Nalbant M, Gökkaya H, Sur G (2007) Application of Taguchi method in the optimization of cutting parameters for surface roughness in turning. Mater Des 28:1379–1385

    Article  Google Scholar 

  39. Sahoo AK, Pradhan S, Rout AK (2013) Development and machinability assessment in turning Al/SiCp-metal matrix composite with multi-layer coated carbide insert using Taguchi and statistical techniques. Arch Civ Mech Eng 13:27–35

    Article  Google Scholar 

  40. Kumar S, Kumar P, Shan HS (2006) Parametric optimization of surface roughness castings produced by evaporative pattern casting process. Mater Lett 60:3048–3053

    Article  Google Scholar 

  41. Thornton R, Slatter T, Lewis R (2014) Effects of deep cryogenic treatment on the wear development of H13A tungsten carbide inserts when machining AISI 1045 steel. Prod Eng Res Devel 8:355–364

    Article  Google Scholar 

  42. Gill SS, Singh H, Singh R, Singh J (2011) Flank wear and machining performance of cryogenically treated tungsten carbide inserts. Mater Manuf Process 26:1430–1441

    Article  Google Scholar 

  43. Motorcu AR (2010) The optimization of machining parameters using the Taguchi method for surface roughness of AISI 8660 hardened alloy steel. Stroj Vestn-J Mech E 56:391–401

    Google Scholar 

  44. Kıvak T (2014) Optimization of surface roughness and flank wear using the Taguchi method in milling of hadfield steel with PVD and CVD coated inserts. Measurement 50:19–28

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Gümüşova Vocational School of Higher Education, Düzce University, Düzce, Turkey

    Sıtkı Akıncıoğlu

  2. Mechanical Engineering, Karabük University, Karabük, 78600, Turkey

    Hasan Gökkaya

  3. Mechanical Engineering, Düzce University, Düzce, Turkey

    İlyas Uygur

Authors
  1. Sıtkı Akıncıoğlu
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Hasan Gökkaya
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. İlyas Uygur
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Sıtkı Akıncıoğlu.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Akıncıoğlu, S., Gökkaya, H. & Uygur, İ. The effects of cryogenic-treated carbide tools on tool wear and surface roughness of turning of Hastelloy C22 based on Taguchi method. Int J Adv Manuf Technol 82, 303–314 (2016). https://doi.org/10.1007/s00170-015-7356-z

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-015-7356-z

Keywords

Search

Navigation