Skip to main content
SpringerLink
Log in

Interfacial properties of diffusion bonded Ti-6Al-4V to AISI 304 stainless steel by inserting a Cu interlayer

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

The joining characteristics of Ti-6Al-4V with AISI 304 stainless steel by inserting a Cu interlayer was investigated in a vacuum-free diffusion bonding process. The diffusion bonds were carried out in the temperature range of 820, 850 and 870°C for 50, 70 and 90 minutes, respectively, under 1 MPa load in argon atmosphere. The joining performances of diffusion bonded Ti-6Al-4V to AISI 304 were studied experimentally. The influence of the insert layer on the microstructure-formed interface region, bonding quality and mechanical properties have also been estimated. The microstructures formed in the diffusion region were observed and determined by scanning electron microscopy (SEM). The microhardness across and perpendicular to the interface were measured and the strength of the joints were also determined with lap-shear test.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. He P, Zhang J, Zhou R (1999) Mater Charact 43:287–292 DOI 10.1016/S1044-5803(99)00008-X

    Article  Google Scholar 

  2. Yeh MS, Chuang TH (1995) Scripta Metall Mater 33:1277–1281 DOI 10.1016/0956-716X(95)00364-2

    Article  Google Scholar 

  3. Ozdemir N, Orhan N, Aksoy M (2003) J Mater Proc Tech 141:228–233 DOI 10.1016/S0924-0136(03)00154-7

    Article  Google Scholar 

  4. Kundu S, Ghosh S, Laik A (2005) Mater Sci Eng A 407:154–160 DOI 10.1016/j.msea.2005.07.010

    Article  Google Scholar 

  5. Kundu S, Chatterjee S (2006) Mater Sci Eng A 425:107–113 DOI 10.1016/j.msea.2006.03.034

    Article  Google Scholar 

  6. Ozdemir N (1996) F.U. Graduate School of Science. Master Thesis

  7. Orhan N, Khan TI, Eroğlu M (2001) Scripta Mater 45:441–446 DOI 10.1016/S1359-6462(01)01041-7

    Article  Google Scholar 

  8. Kliauga AM, Travessa D, Ferrante M (2001) Mater Charact 46:65–74 DOI 10.1016/S1044-5803(00)00095-4

    Article  Google Scholar 

  9. Hidetoshi S et al (2003) Scripta Mater 48:1249–1254 DOI 10.1016/S1359-6462(03)00054-X

    Article  Google Scholar 

  10. Ghosh M, Chatterjee S (2002) Mater Charact 48:393–399 DOI 10.1016/S1044-5803(02)00306-6

    Article  Google Scholar 

  11. Ghosh M, Chatterjee S (2005) Mater Charact 54:327–337 DOI 10.1016/j.matchar.2004.12.007

    Article  Google Scholar 

  12. Travessa D et al (2002) Mater Sci Eng A 337:287–296 DOI 10.1016/S0921-5093(02)00046-1

    Article  Google Scholar 

  13. Yang KCW, Ralph B, Lee WB (1997) J Mater Proc Tech 63:759–764 DOI 10.1016/S0924-0136(96)02719-7

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Department of Metal, University of Fırat, Faculty of Technical Education, 23119, Elazığ, Turkey

    N. Özdemir & B. Bilgin

Authors
  1. N. Özdemir
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. B. Bilgin
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to N. Özdemir.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Özdemir, N., Bilgin, B. Interfacial properties of diffusion bonded Ti-6Al-4V to AISI 304 stainless steel by inserting a Cu interlayer. Int J Adv Manuf Technol 41, 519–526 (2009). https://doi.org/10.1007/s00170-008-1493-6

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-008-1493-6

Keywords

Search

Navigation